Evertz Microsystems Ltd.

Download PDF

7732DVP-HD

HD Dual Link Video Processor

VistaLINK® enabled

The 7732DVP-HD Dual Link Video Processor module is a multi-purpose module designed to convert between 4:2:2 and 4:4:4 HDTV video signals in a wide variety of applications. The model 7732DVP-HD can be operated in a dual link to single link mode for 4:4:4 high definition applications, or 4:2:2 to 4:4:4 mode to convert traditional high definition content to 4:4:4.

The 7732DVP-HD occupies one card slot in the 3RU frame, which will hold up to 15 modules or the 1RU frame which will hold up to three modules.

Features

  • Automatically senses between 1080i/60, 1080i/50, 1080p/24sF, 720p/60 and 720p/50 video formats and the 1/1.001 divisor versions where applicable
  • 4:4:4 Dual Link HDSDI to 4:2:2 HDSDI converter
  • 4:2:2 HDSDI to 4:4:4 Dual link HDSDI converter
  • 4:4:4 Dual Link HDSDI to 4:4:4 HDSDI with LUTs
  • Two serial digital 1.5Gb/s HD inputs per ST 292-1
  • Three serial digital 1.5Gb/s HD outputs per ST 292-1
  • Bypass relay protection on inputs for power failures
  • Retimed 4:4:4 dual link outputs
  • Programmable LUTs for 4:4:4 and 4:2:2 HDSDI to accommodate different colorimetry between monitoring devices
  • Factory LUTs handle logarithmic "filmstream" inputs from VIPER and ARRI D20 cameras
  • Store / recall user presets of common configurations - up to 10 presets
    • 6 GPI control inputs to select operating modes or load user presets
    • 2 GPO status outputs indicate operating modes - programmable functions
    • Card edge menu using OSD on 4:2:2 output to configure the operating modes
    • Card edge LEDs for signal presence, module status
    • VistaLINK® capable for remote monitoring, control and configuration capabilities via SNMP; using VistaLINK® PRO, CP-2116E or CP-2232E Control Panels. VistaLINK® is available when modules are used with the 3RU 7800FR frame and a 7700FC VistaLINK® Frame Controller module in slot 1 of the frame
Block Diagram Block Diagram

Specifications

Serial Digital Video Input
StandardSMPTE ST 372 (dual link 1.5Gb/s) or
ST 292-1 (1.5Gb/s) - auto-detects standard using SMPTE ST 352 Payload ID
SMPTE ST 274, SMPTE ST 296 - 1080i/60, 1080i/50, 1080p/24sF, 720p/60 and 720p/50 and the 1/1.001 divisor versions where applicable
SMPTE 428-9, ST 2048-2 - 2048x1080p/24sF
Number of Inputs1 dual link or 1 single link
ConnectorBNC per IEC 61169-8 Annex A
EqualizationAutomatic to 65m @ 1.5Gb/s with Belden 1694 or equivalent cable
Return Loss> -15dB up to 1.5GHz
Serial Digital Video Output
StandardSame as input
Number of outputs2 dual link outputs (bypass relay protected to inputs) + 1 single link output
ConnectorBNC per IEC 61169-8 Annex A
Signal Level800mV nominal
DC Offset0V ±0.5V
Rise and Fall Time200ps nominal
Overshoot< 10% of amplitude
Return Loss
4:4:4 Outputs> -10dB @ 1.5Gb/s
4:2:2 Output> -6dB @ 1.5Gb/s
Jitter< 0.2UI
Payload IDSMPTE ST 352
GPIO Control Port
Number of Inputs6, programmable functions
Number of Outputs2, programmable functions
TypeOpto-isolated, active low with internal pull-ups to +5V or +12V (jumper selectable)
Connector9-pin female D
Signal LevelClosure to ground
Look Up Tables
Type10 bit 1-D LUT
Number5 factory programmed
5 User loadable
User UploadRS-232, 57600 baud using card edge connector
Input to Output Processing DelayHD Input Video
Video Delay2 lines
Electrical
Voltage+12V DC
Power10 Watts
EMI/RFIComplies with FCC regulations for class A devices
Complies with EU EMC directive
Physical
Number of Slots1

Ordering Information

7732DVP-HDHD Dual Link Video Processor
Ordering Options
Notes• Rear plate must be specified at time of order - eg: [model]+3RU
Rear Plate Suffix
+3RU3RU rear plate for use with 7800FR, 7801FR, 7700FR-C or 350FR Multiframes
+1RU1RU rear plate for use with 7701FR Multiframe
+SAStandalone Enclosure Rear Plate
Enclosures
350FRPortable Multiframe which holds 7 modules
7700FR-C3RU Multiframe which holds 15 modules
7800FR3RU Multiframe which holds 15 modules
7701FR1RU Multiframe which holds 3 modules
S7701FR7700 Series Standalone Enclosure